This service manual describes the latest service information for the ICA VHF/ UHF FM TRANSCEIVER, ICAD. VHF/UHF DIGITAL TRANSCEIVER at the. Manuals and User Guides for ICOM ICAD. We have 2 ICOM ICAD manuals available for free PDF download: Instruction Manual, Service Manual. View and Download ICOM ICA instruction manual online. VHF/UHF FM TRANSCEIVER. ICA Transceiver pdf manual download. Also for: Icad.
|Published (Last):||24 April 2018|
|PDF File Size:||3.66 Mb|
|ePub File Size:||9.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
Operation is sub- ject to the following two conditions: With proper care, this product should provide you with years of trouble-free operation. The transceiver will become hot when op- Changes or modifications to this device, not I Antenna Insert the supplied antenna into the antenna connector and screw down Jack cover the antenna as shown at left.
NEVER carry the transceiver by hold- ing the antenna. KEEP the jack cover attached when jack is not in use to protect the con- nector from dust and moisture. Misuse can also cause damage to the battery or degra- dation of battery performance.
Use and charge only specified Icom battery packs with Icom radios. Only Icom battery packs are tested and approved for use with Icom radios. DO NOT charge the battery outside of the spec- ified temperature range: The battery may heat up or rupture if charged out of the specified temperature range. I Rapid charging The optional BC provides rapid charging of the battery pack.
Detach the battery pack from the transceiver then charge the battery pack by itself, or charge the battery with regular charging when the transceiver power cannot be turned OFF. Fre- quencies for both transmitting and receiving are generated and controlled by the VFO.
Also available for A band operation only. D D Using the keypad The frequency can be directly set via numeric keys. I Setting squelch level The squelch circuit mutes the received audio signal ic–91ad ing on the signal strength.
The receiver has 9 squelch levels, manusl continuously open setting and an automatic squelch setting. About the sweep steps: Transmitting without an antenna will damage the transceiver. To prevent interference, listen on the channel be- fore transmitting by pushing and holding [SQL]. D D Volume setting for dualwatch The volume setting for dualwatch can be set mankal both bands simultaneously or for each band separately in set mode. The offset and repeater tone frequencies are not changed by the auto repeater function, reset these frequencies, if necessary.
I Hz tone Some European repeaters manuwl a Hz tone burst to be accessed. For such European repeaters, perform the follow- ing. However, you must manually over-write a programmed call sign in regular memory and call channels.
Temporary opera- tion without over-writing is possible. This system provides you to with much wider coverage range during digital voice mode ic-91d.
A Gateway Station B The stored call signs are viewable in the following manner. After receiving the reply call, communicate normally. While operating with the call sign squelch Available characters are 0 to 9, A to Za to zsome symbols and space.
ICOM IC-91AD Manuals
OFF, or overwritten when another message is re- ceived. In the EMR communication mode, no call sign set- ting is necessary. Release [PTT] to receive.
The position data is transmitted with your voice sig- Longitude nals at the same time. The DV voice memory is divided into 2 tracks, 15 seconds each in a track, as the default setting. Memory channels in each bands including 50 scan edge memory channels 25 pairs frequencies, respectively.
MW] MR for 1 sec. Names can be a maximum of 8 characters. Push to select memory mode. Enter select memory write mode.
Icom ICAD Manuals
This is useful when search- ing for signals around a memory channel frequency and for recalling the offset frequency, subaudible tone frequency etc. Even if the memory bank contents are cleared, if-91ad memory channel contents still remain pro- grammed. To perform memory scan, 2 or more mem- ory channels MUST be programmed, otherwise the scan will not start. To perform memory bank scan, 2 or more bank channels MUST be programmed, otherwise the scan will not start.
MW] MR several times to select jc-91ad bank mode. In addition, memory channels can be set to be skipped for both memory skip scan and frequency skip scan.
Download Error – Icom America
These are useful to speed up the scan rate. I Scan resume condition D D Scan pause timer The scan pauses when receiving signals according to the scan pause time.
It can be set from 2 to 20 sec. The transceiver has 3 priority watch types to suit your needs. The watch resumes according to the selected scan resume condition. For memory channel watch: Select the desired memory channel. For call channel watch: Select the desired icc-91ad channel. For memory scan watch: Select memory mode, or the desired bank group; then, push and hold [SCAN] 2 for 1 sec.
I General MENU screen is used for programming infrequently changed values or conditions of functions. MENU screen indication for B band. Pushing and holding [SQL] to ic-91d the fre- quency. This function inhibits transmission while receiving a signal or when the squelch is open. D D Auto reply This function replies to an individual station call even you are away from the transceiver. The transceiver sets monitoring mode to FM and DV according to the received signal.
Monitors in DV mode. Msnual D GPS auto TX timer Selects the desired interval for automatic position transmis- sion function from 5, ci-91ad, 30 second, 1, 3, 5, 10 and 30 min- utes. The priority watch is turned OFF. The transceiver checks the memory channel fre- quency every 5 sec.
D D Memory bank link ic-991ad Sets the memory bank link function ON default link function provides continuous bank scan, scanning all con- tents in the selected banks during bank scan.
When a call is received, the calling station call sign can be in- dicated oc-91ad. Opening logo indication is skipped. The set your own call sign, programmed in my call sign, can be displayed at power ON. Transfer the DTMF data per about msec. S-in- dicator shows signal strength. By monitoring a signal that is being transmitted on a repeater input frequency, you can determine the tone frequency required to access the repeater. Shows above indications alternately.
While receiving a signal on a frequency other than the weather alert ON frequencythe receiving signal or audio will be interrupted momentarily every 5 sec. This may be caused externally by static electricity or by majual factors.
If this problem occurs, turn power OFF. After waiting a few seconds, maanual power ON again. If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center.
No power comes ON. Already installed into the ICAD. Remote control functions can be selected from 3 settings. Page of Go. Table of Contents Add to my manuals Add. Explicit Definitions With proper care, this product should provide you with years of trouble-free operation.
Accessory Attachment I Antenna Insert the supplied antenna into the antenna connector and screw down Jack cover the antenna as shown at left. Battery Charging Misuse can also cause damage to the battery or degra- dation of battery performance. Page 25 D D Using the keypad The frequency can be directly set via ic-91ar keys. I Setting Squelch Level I Setting squelch level The squelch circuit mutes the received audio signal depend- ing on the signal strength.
I Lock Function p. Page 33 D D Volume setting for dualwatch The volume setting for dualwatch can be set for both bands simultaneously or for each band separately in set mode. Page 43 However, you must manually over-write a programmed call sign in regular memory and call channels. I Break-in Communication After receiving the reply call, communicate normally. Page 59 OFF, or overwritten when another message is re- ceived.
Page 93 95 p.