May 15, 2020

Correction in Service Manual. CX New camera body – new parts .. The operation (except ELX) is fortunately a matter of minutes only. Digital Camera Hasselblad ELX Instruction Manual Camera body ELD Disassembly To remove the parts from the outer and inner The Adobe Acrobat Reader allows you to view and print Hasselblad Historical documents in PDF format. A free copy of the Acrobat Reader is available from.

Author: Gukinos Tedal
Country: Vietnam
Language: English (Spanish)
Genre: Life
Published (Last): 6 May 2013
Pages: 464
PDF File Size: 13.70 Mb
ePub File Size: 2.27 Mb
ISBN: 219-8-90285-794-9
Downloads: 84956
Price: Free* [*Free Regsitration Required]
Uploader: Yozshubei

This way, you won’t get caught with two dead batteries. If the mirror spring in the body breaks, you’ll know it because the body will jam up.

Are the batteries flat or incorrectly inslatted? This booklet is an effort to save people money on their repairs, and also save them the all the time that is involved. One of my customers got a call from his lab, informing him that every negative he shot at a wedding was three to four stops overexposed.

Why did you replace the light trap and nylon stop in my film magazine? The manual goes out of its way to be unhelpfull, with the bit about checking the battery miles from the other sections about the battery, and it does not say if a blown furse prevents you getting a “good battery reading” on the em test LEDs, but I think there is only one fuse, manula if it manuaal you cannot wind on or do very much at all with the camera.

Hasselblad camera repair and maintenance advice.

A repair manual such as this, is available no other place in the world, as these are closely held secrets of the repair trade. That should of course mankal “film” and “digital”.

Next, turn the transport key forward through nine complete turns. Do not use this procedure with any motorized body or any body with a focal plane shutter curtain! The smaller screw to the left of that one is actually slm a screw at all; it is the slotted end of the front key shaft.


Back to Top How can I check my camera to make sure that it is working properly? It also prevents the camera from firing when the dark slide is inserted, and prevents the removal of the film magazine from the camera mnaual when the dark slide is removed. When I overhaul a film magazine, I usually replaced the light trap and nylon stop.

HASSELBLAD Camera Manuals

As the nylon stop wears, the opening in the magazine gear gets lower and lower. Can be set for normal or digital photography.

Camera body ELD Adjustment Check that the magnet arm has free movement between the shanks of spring during exposure.

If you send me a film back for repair and the dark slide is bent or warped, I may replace it without you asking me to. Insert the dark slide in the magazine and try to fire the body.

It should of course be “set to ‘O’ ” Did you ever get your film back from the lab, hassleblax to discover there was a problem, such as a light leak or bad film spacing, and you didn’t know which magazine was the culprit? Locate the mirror into position.

Hasselblad 555ELD Service Manual

EPS Fig. Look into the front of the lens and fire the camera.

Front bayonet plate and auxiliary shutter Exploded view: Fit the washer followed by the B-armthen fit the washer followed by the S-arm Use the lubricants listed below: I often keep the button in the manuaal hole when I am using a wire release – is your release button in the right hole? Motor housing Exploded view: When you wind the camera, the number in the film counter window should advance to the next number.


Is your Haasleblad working now? To illustrate a point eepair no photographer should ever forget:. Your first reaction is to try to wind the body.

Thank you in advance internet. If you see part of the shutter blades instead of a round hasslblad of light, there is a problem, and that lens should not be used. Tighten the locking screw. When the tripod foot and the rubber support have been removed, four hassldblad are exposed allowing access to the four screws Page 10 Camera body ELD Disassembly To remove the parts from the outer and inner mounting plates proceed as follows see the exploded views 13 and Check that the auxiliary shutter blinds do not influence on the light path.

When I overhaul a lens, I usually replace the flash contact and the main spring. Place the roll hasslrblad film on the supply side of the spool holder and pull out a short length of paper leader.

The lever should lock in this position. Why did you install or replace the brake assembly in my camera body? This manual will be a photocopy of the original. In latethe entire configuration of the gears, springs and arms in the body was modified, along with the brake assembly.

I recommend, however, that you only use one battery at a time in your camera. Camera body ELD Disassembly To remove the parts from the outer and inner mounting plates proceed as follows see hassleblaad exploded views 13 and