CP2E – read user manual online or download in PDF format. Pages in total: from the Crestron website (). 2. CP2E only. 2- Series Engine. At the heart of the CP2 & CP2E is the powerful bit Freescale. Crestron CP2E Pdf User Manuals. View online or download Crestron CP2E Operation Manual.
|Published (Last):||6 November 2006|
|PDF File Size:||6.18 Mb|
|ePub File Size:||7.73 Mb|
|Price:||Free* [*Free Regsitration Required]|
Refer to table at right. Enclose a note specifying the nature of the problem, name and phone number of contact person, RMA number, and return address.
Example Program Detail View. Use Crestron Certified Wire.
Page 2 This document was prepared and written by the Technical Documentation department at: Refer to software release notes or Crestron website for other required Crestron software packages. Enter text from picture: You may not reverse engineer, decompile, or disassemble the Software.
Failure to do so could cause equipment damage or void the Crestron warranty. In the event that the clock fails, only an authorized technician should replace it. If power is supplied through an AC adapter, verify the DC output plug is properly attached to the control system and that the adapter is securely plugged into an outlet.
For more details, refer to the Crestron Toolbox help file. Shipments arriving freight collect or without an RMA number shall be subject to refusal. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Creetron to do so may incur additional charges if support is required to identify performance deficiencies because of using improper wire.
If Cresnet units are to be daisychained on the run, the Cresnet power usage of each network unit to be daisychained must be added together to determine the Cresnet power usage cresron the entire chain.
You shall not remove or conceal any trademark drestron proprietary notice of Crestron from the Software xp2e any back-up copy. However, before attempting to upload or upgrade, it is necessary to establish communication.
Cresnet power usage of the entire chain. Page 28 Crestron Electronics, Inc. Strip and Tin Wire When daisy-chaining Cresnet units, strip the ends of the wires carefully to avoid nicking the conductors. Got it, continue to print. Verify that serial cable is wired correctly for RS, or Consideration must be given if installed in a closed or multi-unit rack assembly since the operating ambient temperature of the rack environment may be greater than the room ambient temperature.
Therefore, if you use a PWRU power supply rated at 50 wattsyou will have 26 watts of power left over to run additional Cresnet devices. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Crfstron only Every Ethernet-enabled 2-Series control system works directly with Crestron’s exclusive RoomView Help Desk software for the industry’s most comprehensive facility-wide asset management solution.
Therefore, if you use crrstron PWRU power supply rated at 50 wattsyou will have 26 watts of power left over to run additional Cresnet devices.
In the event repairs manjal found to be non-warranty, return freight costs shall be paid by the purchaser. Device is not receiving sufficient power. Page of 28 Go.
CRESTRON CP2E 说明书_百度文库
To prevent bodily injury when mounting or servicing this unit in a rack, take special precautions to ensure that the system remains stable. As long as the sum total of the devices on Cresnet does not exceed 26 watts, you will be fine.
You may not transfer the rights of this Agreement to a backup copy unless the installed copy of the Software is destroyed or otherwise inoperable and You transfer all rights in the Software. Trademark Information All brand names, product names, and trademarks are the sole property of their respective owners. Crestrron Strip Installation The 2-Series integrated dual bus control system is supplied with two brass bussing strips to facilitate commoning linking of multiple terminal block connections.
Also See for CP2 Operation manual mannual 40 pages. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. To print the manual completely, please, download it. It is functionally the same; only the labeling has changed. Don’t have an account? Loosen the terminal block screws and insert the first leg of the bussing strip into the first common position of the terminal block.
Position a rack ear so that its mounting holes align with the holes vacated by the screws in step 1. If further assistance is required, please contact a Crestron customer service representative.
First-time users will need to establish a user account to fully benefit from all crestdon features. Complete the following procedure to attach the ears to the unit.
Furthermore, this warranty does not cover any product that has had the serial number or license code altered, defaced, improperly obtained, or removed.
Crestron electronic CP2E User Manual
Use only Crestron power supplies for Crestron equipment. If the unit is a home-run from a Crestron system power supply network port, the Cresnet power usage of that unit is the Cresnet power usage of the entire run. Crestron shall, at its option, repair or replace or refund the license fee for any Software found defective by Crestron if notified by you within the warranty period. Particular attention should be given to supply connections other than direct connections to the branch circuit.
Ethernet CP2E only Crestron pioneered the IP-based control system to harness the vast possibilities of Ethernet and the Internet for remote control, monitoring, programming and diagnostics. Crestron recommends that you use the latest software to take advantage of the most recently released features.
Connects to Cresnet control network.