The 3G3MV is a miniature frequency inverter incorperating an open loop vector control Furthermore, the 3G3MV suppresses the revolution fluctuation caused. OMRON products are manufactured for use according to proper procedures by a qualified .. 3G3MV-P10CDT Operation Manual (this manual) and the CPM1/. A maximum of four errors can be displayed. U Software No. OMRON use only. U Output power. W. Monitors the output power of the Inverter (see note.
|Published (Last):||21 August 2007|
|PDF File Size:||11.26 Mb|
|ePub File Size:||17.4 Mb|
|Price:||Free* [*Free Regsitration Required]|
Save to parts list Save to parts list. Page Maintenance Operations Chapter 8 Check and correct the setting in n If the motor is running with no problems and the machinery system is vibrating with a high-pitched whine, it may indicate that this is occurring.
There may be resonance between the characteristic frequency of the mechanical system and the carrier frequency. Error Not used Parity error 1: Press the Enter Key. Page Communications Chapter 7 Parameter Description Next process Determines which step is to be processed next or finishes the operation after the step is finished normally. Refer to page Proper use and handling of the product will ensure proper product performance, will lengthen product life, and may prevent possible accidents.
3g3mb, what 3g3mb you were able to see a piece of equipment before you purchased it? Chapter 5 Basic Operation Operation in Vector Control The Inverter in vector control mode calculates the vector of the operating condition of the motor.
The frequency reference through analog input will be ignored if the Digital Operator has been selected for frequency reference settings. The data of the specified parameter number is displayed. The vibration can be suppressed by setting the derivative D time to a smaller value.
Maintenance Operations Chapter 8 4. This function is used to improve speed accuracy when operating with a load.
Omron 3G3MV-AB004 (3G3MVAB004)
Instead, the front cover is used as a terminal cover and two U-shaped cutouts are provided in place of the mounting holes.
Save okron item to a new parts list. Doing so will result in damage to the Inverter or cause other parts to burn. Series Communications Board Mounting method U01 will be displayed. We’ll send you an email letting you know exactly when your piece of equipment will be available for viewing Name: Keeping the metal pipe at least 30 cm away from the signal line considerably reduces induction noise.
Advanced Operation Chapter 6 This chapter provides information on the use of advanced functions of the Inverter for operation. List of Parameters Chapter 10 Multi-step Signals to select fre- speed ref- quency references 1 erence 1 through Communications Chapter 7 Setting the Communications Data The following description provides information on how to convert the regis- ter data such as monitor value or 3g3nv set value data in the commu- nications data block of the message data such as DSR and response data.
Inputs into these terminals have a variety of functions according to the application. Don’t show me this message again. Furthermore, set the Inverter to this mode if the Inverter is connected to more than one motor or spe- cial motors such as high-speed motors. Communications Chapter 7 Byte No.
At that time, the Inverter will not operate if input in 2-wire sequence is ON. Select the method according to the operation mode.
Page 62 Design Chapter 2 D Solderless Terminals for Control Circuit Terminals The use of solderless terminals for the control circuit terminals is recommended because solderless terminals are easy to connect securely. Thank you for submitting your InstraView Request!
Omron 3G3MV-AB (3G3MVAB) – Axdos AB | PLCSWEDEN | Automation Spare Parts
Outside set range Verify fault 1: Select the CRC check code and set the initial value to D Checking the Nameplate Wire them by providing a common Note 2. Function RUN command 1: Design Chapter 2 D Countermeasures against Induction Noise As described previously, a Noise Filter can be used to prevent induction noise from being generated on the omdon side.
Writing 1 to 2 Not used Upper and lower limit error 1: Maintenance Operations Chapter 8 Lengthen the acceleration time or reduce the load.
Fault reset Multi-function input 1 1: